Hello, Check the steps below how to change turn signal switch. Very first disconnect battery cable. Disable wait bag system. Remove steering wheel. Remove knee bolster if necessary. Remove bolts and also screws and also the lower and upper obelisk cover. Eliminate lock cylinder, if necessary, remove wiring harness strap. Disconnect steering column electrical connector. Disconnect revolve signal and also multifunction move gray and also black connector. Eliminate turn signal and also multifunction move from the vehicle. Inspect the diagrams listed below how to remove and also reinstall revolve signal switch. Check out the diagrams (below). You re welcome let us know if you require anything else to acquire the trouble fixed. Give thanks to you.


You are watching: How to replace turn signal switch chevy s10

\"*\"

\"*\"

\"*\"

\"*\"

\"*\"

electrical problem1995 Chevy S-10 4 cyl two Wheel Drive manual I replaced the signal switch and also the rotate signals and also and back brake lamp don\"t work-related the high back brake light functions I need suggestions on how to operation a examine on this two systems I checke the ground and relay require help.
at the revolve signal switch connector wires check for power at violet wire while an essential in On place -you should have actually battery power. If not replace the trun signal flasher. Also depress the brake pedal and test for power at the move again -brown and white you should have actually battery voltage-If the above 2 check outs the rotate signal is defective-Double examine the rotate signal connections-See EWD

\"*\"

\"*\"

\"*\"

\"*\"


I replaced the rotate signal switch now I have actually no turn signal or ago brake lamp I checked fuse\"s I placed the old switch ago in it does the very same I think I have actually a ground trouble the top brake light functions I require some idea\"s on how to inspect this out any type of info would be helpful. Thanks.
test the turn and also hazard flasher also check ground black wire at rear of ideal cylinder head. Likewise test the high mount protect against relay located at ideal rear that engine compartment. View below

\"*\"

\"*\"

\"*\"


I changed signal switch i now have no rotate signal and back brake light the high brake light works I checked the ground and relay. I think I have actually somting the is not associated I have actually a open con. Top top left beside beside lt. Switch it has actually purple lt blue lt eco-friendly grey and also black v white stripe wires the lt. Blue cable is hot at all times I check out no connection.I need assist what deserve to I do.
try a new switch, the sounds prefer it hasnt to be hooked up correctly or the switch is bad, go back and retrace. If friend post back ill try to find you a wiring diagram for it.
can the male and female push pull plug be changed indivudally I confirm brake switch it\"s yes what else need to I inspect don\"t be in a rush I will be gone because that 3days.
You said to examine brake light switch and push pull plug top top multifunctual switch i assumed you were talking about the signal switch if not please explain. And any various other thing i could check to acquire my brake lights and also signal move working.
i was asking what plug you room talking about. If the fuses space all an excellent and you have no revolve signals or brake lights, that is most most likely the turn signal switch.
Yes yet I have actually replaced the signal move after I changed the head I damaged the emergency flasher\"s.I also replaced the wire\"s come the starter switch. You claimed to examine the push pull plug i assumed that was the plug indigenous the signal switch, if not please describe I to be the an initial to say ns am not a standard mechanic any new ideas room welcome.
If you changed the revolve signal switch and all fuses space good, you can need to take it to a qualified tech. Go you litter away th eold switch? If not enhance up the plug to be sure that every the wires space in the same spots. There is a seperate little wiring set for the multi-function switch, the plugs in down near the turn switch plug
My rotate signal move is broken and also has no function, wipers, hi/low beams. Any great information on exactly how to readjust it out?


See more: Pressed For Time Ac Odyssey, Pressed For Time Quest Walkthrough (Updated)

great evening, ns attached the procedure below for you through a snapshot for you to view.Roy1. Disconnect battery floor cable. 2. Remove steering wheel. WARNING: refer to Air Bags and Seat Belts/ air Bags (Supplemental Restraint Systems)/ Service and Repair/ waiting Bag mechanism Disarming & Arming. 3. Using a screwdriver, pry cover from lock plate. 4. Utilizing lock plate compressing tool No. J-23653, or equivalent, remove lock plate together follows: a. Compress lock plate and pry retaining ring native groove top top shaft, Fig. 5. B. Slowly release lock plate compressing tool, then eliminate tool and also lock plate from shaft end. 5. Slide canceling cam and upper bearing preload feather from finish of shaft. 6. Remove turn signal (multi-function) lever. 7. Remove hazard warning knob retaining screw, button, spring and knob. 8. Eliminate pivot arm. 9. Remove switch retaining screws and pull move up indigenous column, guiding wire harness with column.10. Reverse procedure to install.