Rider and passenger safety rely upon the correct installation of this kit. Use the suitable service hand-operated procedures. If the procedure is no within her capabilities or you perform not have actually the correct tools, have a rwandachamber.org dealer perform the installation. Improper installation the this kit could result in fatality or severe injury. (00333b)
This instruction paper references organization Manual information. A business Manual because that your design motorcycle is forced for this installation and also is accessible from a rwandachamber.org Dealer.

You are watching: How to remove harley rear turn signals


WARNING
To prevent accidental car start-up, which could reason death or major injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a)
WARNING
Disconnect negative (-) battery cable first. If confident (+) cable should call ground with an unfavorable (-) cable connected, the resulting sparks can cause a battery explosion, i m sorry could an outcome in death or major injury. (00049a)
Refer come the applicable business Manual section covering Amp Multilock electrical Connectors. Eliminate front left and also right rotate signal wiring indigenous connectors. Eliminate turn signals from present mounts. Make keep in mind of cable strap places for use when installing brand-new signal wiring in place.
Remove acorn nut and also lockwasher hold left side rear watch mirror in place, but do not eliminate mirror.
Place ball stud (3) through ball stud clamp (2) and also thread top top jamnut (6). Screw sphere stud assembly into left side lamp housing. Tighten jamnut against lamp housing.
Attach lamp real estate to handlebar housing by screwing sphere stud clamp ~ above receptacle. Allude turn signal right ahead climate tighten sphere stud clamp securely to hold lamp in place.
Remove acorn nut and lockwasher holding ideal side rear check out mirror in place, yet do not eliminate mirror.
Place continuing to be lockwasher (5) over end of rear watch mirror, then screw retainer (1) onto end of mirror to organize mirror in place.
Place round stud (3) through ball stud clamp (2) and thread ~ above jamnut (6). Screw round stud assembly into right next lamp housing. Tighten jamnut against lamp housing.
Attach lamp real estate to handlebar real estate by screwing round stud clamp onto receptacle. Suggest turn signal directly ahead then tighten ball stud clamp securely to organize lamp in place.
Route wiring native kit come connector locations and cut wires come length. Following applicable indict from business Manual, download terminals to wires and also install to connectors. Girlfriend connectors and install cable and install cable straps from kit at initial locations.
\"*\"

Prior to removing rotate signal wires, very closely note routing. In specific pay close attention to the areas of the cable straps which must be replaced.
When removing rotate signal wiring, describe appendix in applicable business Manual covering in-depth procedures for Amp Multilock electric Connectors.
1998 and also Earlier Models; eliminate seat and also disconnect connector halves at connector <7>. Complying with instructions in applicable service Manual, eliminate left and right revolve signal wiring native connectors.
1999 and Later Models; eliminate left and right rotate signal 2-pin connectors from circuit plank (inside behind tail lamp). Complying with instructions in applicable company Manual, eliminate left and right revolve signal wiring native connectors.
\"*\"

When performing the next step, use Terminal P/N 72039-71 for 1995 and earlier models. Usage Terminal P/N 73191-96 for 1996 and also later models.
When performing the next step on 1994 and earlier models, terminate the ground cable (Black) utilizing ring terminal P/N 9858 and also secure to ground screw or other suitable location. For power wire, usage terminal as defined in ahead note and also route adhering to same course as original.
Following instructions in service Manual extending Amp Multilock electrical Connectors, crimp brand-new terminals on wires from kit.

See more: 3 Best Vpns For Age Of Empires 2 Hd Lag Fix Es Framerates On Higher


1998 and Earlier Models; Insert terminals into connector <7> (under seat). Mate connector halves. 1999 and also later Models; Insert terminals into 2-pin connectors. Install connectors come circuit board (inside behind tail lamp).
WARNING
Connect positive (+) battery cable first. If optimistic (+) cable should call ground with negative (-) cable connected, the result sparks can reason a battery explosion, which could an outcome in death or significant injury. (00068a)
After installing seat, pull increase on seat to be sure it is locked in position. When riding, a loose seat can shift causing lose of control, i beg your pardon could result in death or major injury. (00070b)
Be sure headlamp, tail and also stop lamp and turn signals room operating properly prior to riding. Poor visibility of driver to other drivers can an outcome in death or major injury. (00478b)