marineyeh 3DR SOLO 3DR, balance, drone, gimbal, HDMI Cable, mod, ribbon HDMI Cable, SOLO, sorbothane, Stabilization


Many people replace their stock HDMI Cable together a an initial solution to reduce the vibration, so perform I.But not everyone use the Ribbon Cable, and…many ppl faces new problem after they adjust the HDMI Cable.In this article I will display you:1. What to carry out if friend don’t have actually ribbon cable, yet you want to reduce the vibration from stock cable.2. Hazard of HDMI Cable Replacement, and How To settle IT.3. Some other problems related to gimbal.

You are watching: 3dr solo hdmi cable

About “How to dissemble my SOLO.”Please refer to this video~(I’m not offering it, ns think it’s quite enough for girlfriend to change the HDMI cable.)

1. What to perform if friend don’t have ribbon cable, yet you desire to alleviate the vibration from stock cable.In the very first post “3DR SOLO mode Diary-01-Stabilize 101” there is a Rule B- settle Every thing Which can Vibrate.

As the picture below depicts…The share HDMI Cable have “only” 3 points fixed(A, A’, B).Point A connected with SOLO and allude A’ linked with gimbal.Point B was resolved by Cable Tie as soon as you open your SOLO.(I didn’t tie that back)

*
Point C is a Ferrite Bead which is heavy and just hang end there there is no support.Under this structure, vibration easily come indigenous the section of D-C-D’ the the HDMI cable.Many SOLO pilot talk around “reroute” the HDMI Cable, which method they want to find some nearer assistance to settle the cable and also reduce the vibration.

What i did is shot to discover something the can offer support near suggest C .As you deserve to see below~there space two protruding structure as screw hole in suggest D and allude D’.

*
I use cotton cord to host the HDMI Cable and also the Screw Hole.My pointer is …doing this after friend putting earlier of your gimbal(and connect the HDMI Cable v the Gimbal).It work-related quite well~

*
Please take it a watch of this video clip for part details difficult to presented on picture.

If you can…try to bind other wires at the very same time…I use the cotton cord come tie the HDMI Cable and the Motor wire at the exact same time.I will adjust it come Ribbon Cable, therefore this is temporary for me.Use Ribbon Cable no only reduce the possibilities that vibration generation…but likewise reduce the weight a lot…

*
*
The weight matter since it regarded the complete balance the the drone and the payload.Lighter is always better.

2. Hazard of HDMI Cable Replacement, and also How To deal with IT.Before i replacing the HDMI Cable…some ppl said me the the Ribbon Cable is no durable, and finally they change back come the share HDMI Cable.Talk about my experiences~Flight right after I change to the R3D Ribbon HDMI Cable is awesome.But soon I suffer from the unusual display screen feed!!Ever since my SOLO fly, my screen feed was getting choppy, it simply move off the bottom again and also again prefer what had constantly shown on old TV.Every trip it just getting worse and finally show only black.

*
That took me a month to resolve it.And say thanks to GOD I saw a discussion around it ~ above FB’s “3DR SOLO owners group” as soon as I to be going to provide up.I cannot discover that discussion now yet from that ns knew one point is that…The HDMI Socket of SOLO body and also Gimbal are not solder well.If you disassemble the HDMI cable often like me, of food it will certainly die/loose virtually right away.Even you’d never ever do that, it could just occur on her SOLO.
*
So the best means to fix it is to glue the location where arrow pointed, push the socket before dry, do it affix well, the choppy image feed comes from the disconnection as soon as vibrating/flying.I use UV glue, works very well.The choppy photo feed happened on both my two SOLO, and also all solved up by UV glue.Please try if you are having the exact same problem.Don’t need to re solder them, of course if you have the right to do that, it will be awesome.

BTW…you can likewise glue the connection component of the Ribbon Cable.

*
*

Before putting ago the battery tray, please do the last thing.1. Assemble the gimbal before put back the battery tray.And make certain after girlfriend connecting the stock HDMI Cable to the gimbal, the circle have the right to keep in the center.Sometimes your Stock HDMI Cable may put it the end of center if friend didn’t an alert it.(So i recommend in the beginning…tie suggest D and D’ after affix the gimbal.)And if you ever before crash her SOLO, it could be more easy to off the center.My first SOLO when flip upside down when landing, after that the circle quickly off the facility after i tuning it.

*

2. Put some sorbothane in between the tray and also the SOLO’s motherboard.It will additionally give some aid to mitigate the vibration.

*

————————————-Further more…I’v make the efforts these…if you space interested…pls continue reading.Pls don’t do it, it simply waste time and also doesn’t work.When the jumping image begang, my presumption is that it effected by Electro Magnetic Interference(EMI) since the ribbon cable didn’t have the Ferrite Bead.

See more: Is Wild Kratts On Netflix ? 'Wild Kratts' On Netflix

*

So ns wrap it increase by aluminum silver paper to safeguard from EMI effect ▼.Useless!!!

*

Then i tried to add this Ferrite Bead ~ above the HDMI Cable ▼.Useless!!!

*
*

The Ribbon Cable is not experience from EMI~I’m sure.As come my engineer friend’s recomand… I likewise tried to make “ground connection” the it.The result is…no…not this kind of problem.